Hammond 150

SERIES 150-THE ADDITIVE INJECTOR FOR LOW-FLOW DELIVERY SYSTEMS
The Series 150 system offers the ability to inject single or dual additives at flow rates from 7 to 75 gallons per minute (gpm). Ideal applications include self-fueling cabinets, home heating oil delivery trucks, and lowerflow aviation fuel delivery trucks. This unit is also easily adapted to water treatment. In keeping with Hammonds fluid injection technology, the 150 offers the ability for the user to provide customer-required additive packages for improvement of final product. This scaled-down version of the popular 600 Series allows for installation in limited space, while offering economical, required additive injection.

150-pict.gif (34819 bytes)

COMPLETELY SELF CONTAINED UNITS
The efficient Hammonds fluid powered turbine "borrows" just enough energy from the flowing product line to do the job. No need for electricity, air or pressurized additive lines.

TOTALLY UNASSISTED INJECTION
Complete, passive operation means they automatically operate when the rest of the system operates. No need to remember to turn the injector on or off. If it is connected to a system, it "remembers" when to run, how much to run and when to stop. The operator has nothing to remember, nothing to adjust, nothing to forget.

METERS AND PULSERS ARE NOT REQUIRED
Because our fluid motor acts as both a source of control and power, additional meters and pulsars are not required.

INSTALLATION IS SIMPLE AND ECONOMICAL
With a Hammonds system, there is only one simple mechanical pipe connection. No wiring in hazardous conditions, no additional equipment on other parts of the system to install, no concrete work, or costly site engineering to layout pipes, conduits, pumps and skids. In most cases, a system can be ordered that will "drop in" to your existing piping, requiring very little on-site preparation.

GUARANTEED PRECISION BLENDING
Unlike some systems that inject large slugs into the product at metered intervals, the Hammonds injector continuously dispenses a precise measured rate of additive that matches the existing flow rate. There are no gaps in the injection process. Since the injection point is usually upstream of the fluid motor, thorough blending of product and additive is achieved.

SPECIFICATIONS

NUMBER OF ADDITIVES
One (1) standard
Two (2) Optional
INJECTION RATIOS
One (1) additive
0-600 PPM with standard 1S Head
0-1250 PPM with optional 2S Heads
MINIMUM INJECTION RATIO: 1 PPM
NORMAL OPERATING RANGE: 15-75 GPM
MINIMUM PRODUCT FLOW RATE: 7 GPM
MAXIMUM PRODUCT TEMPERATURE: 0-150° F
MAXIMUM PRODUCT LINE PRESSURE: 100 PSI
(PSI capacity varies with injection ratio, consult factory for requirements greater than those specified)

PRODUCTS VISCOSITIES: to 10,000 SSU
ADDITIVE SUPPLY REQUIREMENTS: Flooded suction
PRODUCTS HANDLED: Ideal for low viscosity materials with some lubricating qualities.
FLUID CONNECTIONS
Product: 11/2" Victaulic Connections
Additive: 1/4" FMNPT standard
MATERIALS OF CONSTRUCTION:
Fluid motor: Anodized Aluminum
Additive injector: All wetted parts 300 series
Stainless Steel
Elastomers: Buna-N, Teflon, Viton

ON/OFF OPERATION
Additives can be turned on or off at pump or with an optional remote control panel with sight flow indicators.

ADDITIVE SUPPLY
Flooded suction is preferred, moderate suction lift is acceptable.

RATIO STABILITY AT LOW FLOWS
Even if startup and shutdown flow rates are below stated minimums, unit can be calibrated to maintain overall ratios. The system will maintain ratio for total product throughput.

LOCATION
No restructions on mounting adjacent to turns, valves or other pipe fittings.

BACK PRESSURE
Pressure and flow rates are not significantly affected. Differential pressure at 75 GPM - 3 PSI

MOUNTING ATTITUDE
Units can be installed in vertical or horizontal lines. The output shaft on the fluid driver should be arranged in a horizontal position.

STANDARD EQUIPMENT
· 150 series fluid motor
· All anodized cast aluminum housing
· 1½" victaulic connections
· Hammonds 1S single, small fluid end injector pump
· All Stainless Steel wetted parts
· 2-way Inject/Calibrate valve
· Adjustable "while running" calibration
· Teflon elastomers
· Stainless Steel check valves
· Stainless Steel injector manifold
· Calibration port
· Built-in injection point with check valve
· Instruction manual with calibration charts
· Graduated calibration bottle
· White acrylic enamel paint
· Factory loop tested to customer's specifications

OPTIONAL EQUIPMENT
· Custom product line fittings
· 1 ½" or 2" flanges
· Suction Strainer
· Suction sight flow indicator
· Suction on/off ball valve, Stainless Steel
· Remote control panel
· Remote electronic controls
· All Stainless Steel construction
· Teflon coated internal
· Epoxy coated internals
· Custom additive tanks
· Weatherproof enclosures
· Multiple additive capability